Journal of Iranian Chemical Engineering (Farsi Edition)
Year:2015 | Volume:14 | Issue:79|Papers Count:9

Biodiesel production from vegetable oils showed to have a great potential as a substitute of fossil fuels. The oil content of rice bran can be used as a raw material for biodiesel production. In the present work, biodiesel was produced from rice bran oil through transestrification where methanol and KOH were used as alcohol and catalyst, respectively. The effects of process variables including Alc./Oil molar ratio, catalyst concentration, temperature and reaction time were investigated. A central composite rotatable experimental design (CCD) was applied to evaluate the effects of the aforementioned variables on the process. The investigated response variables were biodiesel and glycerol yields. Under optimum condition, a biodiesel yield of 90% was obtained at the following conditions: Alc./Oil molar ratio 12: 1, KOH concentration 0.75% of oil, temperature 52.4oC and time 45 min. This result was verified by conducting an experiment under optimal condition where a yield of 85.07 % was achieved.

Coagulation process is of vital importance for achieving good performance in water pre-treatment units. It usually implements optimum operating conditions that results in highest turbidity removal. The choice, dosage, pH and rate of mixing of coagulant and coagulant-aid are the variables that define optimum operating conditions. In this research, coagulation process of Fajr petrochemical company has been studied. Several jar tests are conducted to determine performance of Alum, Ferric chloride and Poly aluminum chloride as coagulants and anionic poly electrolyte and wheat starch as coagulant-aids at different pH and mixing rates.Optimum operating conditions data obtained in jar tests are used in developing a Neural Network model. This model allows operators to have an estimation of the operating conditions. The success of water pre-treatment depends on fixed feed water quality without frequent need to run jar tests. The predicted result of this network for operating parameters, presented the high consistency with operating data of industrial unit. The maximum relative error for prediction of turbidity is 0.6 % and for total hardness is 2.3 %.The number of neurons of Neural Network hidden layer is optimized and the developed model is validated and tested using a fraction of data that was not utilized in network training. The estimated operating condition for a given feed water quality is implemented in practice and the result of pre-treated water quality matched the expected quality.

In this paper, the effect of various amount of bone ash in bone china bodies while the firing temperature is constant has been investigated. The samples were characterized by XRD, XRF and SEM. It was observed that increasing the bone ash content leads to more intense b-tricalcium phosphate (b-TCP) and anorthite peaks but less intense SiO2 peaks. It was also observed that bone china bodies with higher amount of bone ash have a more glassy structure than bodies with lower amount of it. In bodies with low amount of bone ash and consequently high amount of milled mix, quartz cannot be melted completely and remains as crystals in the structure of body which leads to a body with less glassy structure and a less translucence body. By increasing the bone ash content of bone china bodies, shrinkage, bulk density, module of rapture and thermal expansion coefficient increase while no change can be observed in water absorption. As phosphate has a bleaching effect, increasing the bone ash content in the bone china bodies resulted in a brighter and white body with less colorful tint on the appearance of samples.

In this paper, various affecting parameters on plasticizer migration and mechanical properties of propellant in the composite solid propellants have been investigated. The plasticizer migration phenomenon in steady and unsteady state was also investigated by Fick law’s. Several methods to prevent liquid species migration in the composite solid propellants are described. A computer program based on the mathematical model of Fick’s second Law of diffusion was developed to perform the calculus from the concentration data obtained by experiments. The agreement between the simulated and experimental values obtained from current work validates this model.

The aim of this study is to develop a model for producing combined heat and power from heavy refinery products. To do this aim, two scenarios are developed and analyzed. In the first scenario Integrated Gasification Combined Cycle (IGCC) is investigated as the base case and its related carbon dioxide emitted to atmosphere. In the second scenario molten carbonate fuel cell is added to the cycle in order to improve the performance and reduce carbon dioxide emissions. In the second scenario by reducing 1.5% of net electrical efficiency and 0.97% of cogeneration efficiency with respect to the first scenario, 70% of carbon dioxide emission rate is reduced. Finally sensitivity analysis is performed to investigate the effect of fuel utilization factor on system operational specifications.

In this century water pollution has become a global issue. Heavy metals including Cr (VI) as common environmental contaminants, could be found in different industrial wastewater. Along with the expansion of industry and the increase in the contaminated wastewater, several methods have been proposed for removing contaminants from aquatic environment. Accordingly in this study various methods for the removal of Cr (VI) are presented and in some cases, the removal mechanism of Cr (VI) and the optimum conditions for the process are described. Also the advantages and disadvantages of each technique are presented. So this paper gives the reader a clear direction to find the most suitable separation method for a defined condition.

Recently, carbon nanotubes (CNT) have been investigated by scientific and research centers as well as industrial sections due to the promising electrical, thermo-physical and biological properties. Also, powerful strength and toughness, excellent tensile strenght, Young's modulus and low density of CNT play key roles to select abovementioned structure as a good candidate for production of strong CNT -base yarn. Despite the above-mentioned properties, short length and non-continuos yarn were introduced as a main challenge of researchers to achieve a yarn without defect. In the present work, experimental methods for producing CNT yarn were investigated. The main methods for synthesizing CNT yarn that have been published recently were investigated completely to reach good solution spinning as well as solid-phase spinning. Also, other methods such as electrophoretic and dielectrophorsis spinning have been investigated in terms of performance and compared completely.

In this work, multilayer perceptron network are used to predict the mass transfer flux of CO2 in Piperazine solution. The effective parameters on the absorption flux of CO2 such as interfacial and bulk concentration, CO2 loading, ratio of diffusion coefficient of gas to liquid of CO2, ratio of the CO2 partial pressure to the total pressure, ratio of film thickness of gas to liquid and the film parameter as input variables and mass transfer flux of CO2 as output variables were selected. Experimental data presented in the literature were used for training and evaluating the multilayer neural network of Perceptron. A total of 104 experimental data were used and total concentrations of piperazine were 2-8 mol/lit. The predicting results of neural network indicated that the mean square error for mass transfer flux was 8.61%. In addition, the results of neural network were compared with the predictions of other researchers and the findings revealed that the artificial neural network computes the mass transfer flux of CO2 more accurately and quickly.

Waste materials are being generated around the world every year. Some of these are effectively collected and recovered for use as an energy source or chemical feedstock, while others are simply discarded or burned which in many ways polluting the environment. The improper disposal of these waste materials may constitute an environmental hazard due to the presence of undesirable species such as metals, soot and polycyclic aromatic hydrocarbons. New technologies are being investigated to develop systems which shall support the safe handling, transportation, storage, disposal and destruction of the hazardous constituents of these wastes. The recent interest in microwave technologies due to the extent of the treatments and assisted applications promoting a specific technology has been highlighted against conventional methods, and appears to offer the best alternative to waste management. This paper discusses the potential use of microwave as an energy-efficient mean to current heating technologies employed in the processing and treatment of wastes. The process applications considered are the treatment and control of specific and often problematic waste-streams including; electrical and plastic as well as; industrial and municipal sludge and automotive industry wastes. Moreover, it presents an extensive review of the scientific literature associated with various microwave pyrolysis applications in waste to energy engineering.