Journal of Health and Safety at Work
Year:2014 | Volume:4 | Issue:2|Papers Count:8

Introduction: Chromium (VI) is a known human carcinogenic agent which is used in numerous industrial processes such as electroplating, welding, textile, cement and steel fabrication. The aim of this study was to determine the effectiveness of natural zeolite on the fixed bed adsorption of Cr (VI) from air stream.Material and Method: In this experimental study, chromium mists were generated by a nebulizer (3A model, Italy). Performance of natural zeolite in the Cr (VI) adsorption and its influencing factors such as air flow rate (1 and 3 L/min), the initial Cr concentration (0.05, 0.15, 1 and 10 mg/m3) and the bed depth (2.5, 5 and 10 cm) were investigated.Result: Zeolite adsorption capacity elevated by the increasing of bed depth but decreased with increasing of flow rate and inlet concentration. In order to facilitate the prediction of natural zeolite column performance Yoon-Nelson and Thomas models were used. The results showed that these models have a good agreement with our experimental data.Conclusion: Due to the extensive use of chromium in various industries and regulatory requirements related to workplace health and safety, Cr emission control in the occupational environment is essential. The adsorption process is one of the controlling measures of chromium emissions. The results indicated that natural zeolite has a high efficiency in Cr (VI) adsorption.

Introduction: Whole body vibration occurs when human is on a vibrating surface and the vibration influences parts of the body which are far from the contacted part. Up to now, various health-related problems due to whole body vibration have been reported, including back pain, sciatica, gastrointestinal problems, genital problems and hearing impairment. In the present research, vibration was measured about 2000 minutes in 23 train of 4 active lines of Tehran metro in order to determine the rate of subway drivers’ exposed to whole body vibration.Material and Method: Vibration meter and SVAN 958 analyzer, made by Svantek company, were utilized for measuring the whole body vibration. The level of weighted r.m.s acceleration for each axis, the combination of axes, peak factor, VDV and other common exiting ratios in the standard were measured and calculated according to ISO 2631-1.Result: Findings showed that according to Basic method drivers exposure to vibration is less than the lowest value of health guide critical region (<0.45m/s2). However, based on Vibration Dose Valuation (VDV), the exposure of 12 cases were higher than the lowest value (<8.5 m/s1.75) and only 11 cases were lower than the mentioned amount.Conclusion: Investigation of the result obtained from Basic method and VDV method manifested different amounts of vibration exposure in a way that VDV predicts higher level of risk, compared to basic method. The results shows that some presented indicators can not presented the safe zone in human vibration evaluations.

Introduction: The present study was carried out to compare contrast sensitivity among three groups of professional welders including (1) those who use gas metal Arc welding (GMAW) (2) those who use shield metal Arc welding (SMAW) and the group that uses resistance welding.Material and Method: In this research, all the welders who use GMAW, SMAW and resistance welding working in an industry who were all male, performed contrast sensitivity test, using Freiburg. The contrast sensitivity test was done at three spatial frequency of 1cpd, 5cpd and 15 cpd under a constant condition. The three selected groups were similar regarding age and work experience. The result of the three groups at each spatial frequency were recorded and compared with other groups.Results: ANOVA test showed that decrease contrast sensitivity in spatial frequency of GMAW group at the spatial frequency 15cpd, significantly decrease comparing to SMAW group (p=0.028) and resistance welding group (p=0.041). The mean (SD) of contrast sensitivity at frequency of 1cpd, 5cpd and 15cpd was respectively 140.69±51.8, 172.7±43.75 and 39.8±25.92 for the GMAW group and 157.8±42.2, 183.21±32.01 and 60.57±54.30 for the SMAW group and 149.10±50.68, 180.60±35.42 and 57.38±39.22 for resistance welding.Conclusion: Although all welders use goggle or other personal protective equipment, loss of contrast sensitivity of GMAW workers can be attributed to the cumulative effects of the radiation.

Introduction: Air health is an important environmental issue which has been endangered in recent years due to application of advanced technologies used for improving the financial welfare and relative prosperity of humans. Making use of pollution control systems and refinement methods are some general ways to control environmental pollution. Since several different techniques of control, each with its advantages and disadvantages are employed in order to mitigate the spread of air pollution, the aim of current study was to design a fuzzy multi-attribute decision making model to select the most appropriate air pollution control equipment in Mashhad Shargh Cement Company.Material and Method: After identifying the desired industry and also the production process, all factors affecting decision-making process including environmental factors, technical factors and economic factors were considered by utilizing Fuzzy Analytic Hierarchy Process method. Importance weight of these criteria was calculated and subsequently the priority of model choices were also determined using this approach.Result: Among main criteria of the model, economic criteria was identified as the most important factor influencing the selection of the type of air pollution control equipment, with the wight of 0.555. Environmental and technical factors with weighting of 0.286 and 0.159 also gained the next priorities, respectively. Final weights of Electro filter, Baghouse and Hybrid filter technologies were calculated 0.256, 0.415 and 0.329 in cement mill unit and 0.291, 0.374 and 0.334 in material grinding and furnace unit, respectively.Conclusion: Finally, the proposed model that is based on the Fuzzy Analytic Hierarchy Process indicates that the Baghouse Technique is the most appropriate technique for the purpose of dust filtration in major sources of air pollution spread in Shargh Cement Company.

Introduction: Biorhythm is one of the newest subject in the field of cognition of mental ergonomics which can be very effective in reduction of work-related accidents or mistakes with no apparent reason.Material and Method: This research is a cross-sectional, retrospective, practical and analytical-descriptive study. Delijan cement production company during 2010-2011. Census method was applied and totally 79 accidents (total of the accidents) were investigated. The required information was collected from available documents in HSE unit of the company biorhythm charts were drawn based on a dates of accidents and participants birthdays, using Natural Biorhythm Software V3.02. Human errors were classified according to reason model and were analyzed by SPSS-W software.Result: The results of analysis showed that 40% of accidents have been accrued in usual days and the other 60% in critical days of biorhythm cycle. Regarding errors leading to accidents, it was observed that 95% of accidents were related to human error and 5% related to equipment errors. Moreover, 65.8% of the human errors were associated with the slipping which happens during performing a task, according to reason model.Conclusion: Findings of this research showed that bad and critical days of individuals’ biorhythms cycle influence the occurrence of accidents. Therefore, by training and increasing the knowledge of workers regarding biological cycle and its effects on mental, emotional and physical status, each person effects can make some changes to theire work plans during days that they do not feel well, physically or mentally, in order to prevent the likely accidents.

Introduction: Heat stress is considered as one of the hazardous occupational agents in hot environments. Working under heat stress condition may lead to individuals’ health problems. Several studies have been shown that stress in the working environments can elevate stress hormones such as cortisol. Since heat stress is one of the serious stresses in hot industries including melting, this study was done to investigate the effect of heat stress on the cortisol concentration of workers in one of the melting industries.Material and Method: In this cross-sectional study, 70 workers in two groups of case and control (35 people in case group from foundry unit and 35 people in control group from casting unit without heat stress) were investigated. First, a demographic questionnaire was complete for each subject. Then in order to evaluate the changes in cortisol level, blood samples were taken from the participants during their working hours (9:30 to 10 AM) and the obtained levels were compared with the normal level of cortisol, provided at 7 to 10 AM. In order to assess environmental condition, WBGT (Wet Bulb Globe Temperature) index was measured at three highest including feet, waist and head. Moreover, noise and lighting were measured at the workers work station. Data were analyzed using SPSS software version 16.Result: Regarding WBGT, it was shown that mean WBGT index were 33 C and 16.7 C in case and control groups, respectively. Additionally, cortisol concentration in case group was significantly higher than control group (P<0.001).Conclusion: Results of the present study indicate that physical stresses of working environment can lead to changes in physiology of human body. Thus, variations in hormone level in its consequences in hot environment should be considered in occupational hygine.

Introduction: IBioaerosols are usually defined as aerosols or particles with microbial, plant or animal origin. Textile industries are of the working environments in witch workers are exposed to bioaerosols. In textile industry, the highest contamination concentration is the belonged to carding step. Since, textile industry in iran is native and a large number of employers are working in this industry, this study was undertaken to assess bacterial bioaerosols concentration in a textile in industry in iran.Material and Method: In cross-sectional study was done in different units and also outdoor environment of a cotton textile plant. The concentration of bioaerosols were sampled and measured according 0800 method presented by NIOSH, during summer. Diagnosis of type of colonies and bactories, grown on blood agar, was done using gram staining.Result: The mean bioaerosols concentration obtained the highest and lowest values in outdoor environment (94±9.5 CFU/m3) and unit 2 (Ring site) (64±18.0 CFU/m3), respectively. The mean difference of bioaerosols concentration in unit 1 (Carding sites) and unit 2 (Ring site), was statistically significant in this study. The highest number of bioaerosols colony was for staphylococcus Epiderms (N=1743) and the lowest number was for streptococcus pneumonia (N=64) in the whole plant.Conclusion: Although the bioaerosols concentration obtained in the present study is lower than those reported in other studies, these values are above the threshold recommended.

Introduction: Individuals’ jobs performance is one the most important factors in industries and organizations. The aim of the present study was to investigate the simultaneous effect of exposure to noise, lighting and heat stress on the workers’ job performance.Material and Method: In this analytical-descriptive study, 30 employees of the auto parts manufacturer, in Tehran city, were chosen by simple random sampling. By controlling and limiting confounding factors, the simultaneous effect of noise, lighting and heat stress on the participants’ job performance was investigated, using tow series of mental and manual testes. Data were analyzed by SPSS software version 18, using descriptive statistic, ANOVA and Tukey testes and also person correlation coefficient.Result: The results showed that by increasing the noise and heat stress (P=0.046, r=0.344) and decreasing of lighting (P=0.008, r=-0.472), the required time for performing the Minnesota placement test has been gone up. Moreover, the result revealed that by increase in noise and heat stress (P=0.007, r=0.478) and decrease in lighting (P=0.003, r=0.523) the required time for competing hand tool dexterity test has been also increased at surface and mid level.Conclusion: Finding of the present research manifested that increase in noise and heat stress and also reduction in lighting lessen the speed of manual tests and time and accuracy of mathematical calculations. Therefore this result confirm the effects of various environmental factors on individuals’ job performance, in a way that by variation of different environmental factors, time of manual test and time and accuracy of mental tests would be changed.