INTERNATIONAL JOURNAL OF ENVIRONMENTAL SCIENCE AND TECHNOLOGY (IJEST)
Year:2007 | Volume:4 | Issue:4 (16)|Papers Count:16

In most mining areas, significant concentrations of metals such as Pb, Cu, Cr, Zn, Cd, Fe, Mn, Co, Ni, Hg, Ar, halogenated organic compounds and radionuclides are found. Of those, Cr is one of the well-known heavy metals that forms toxic species. It is necessary to study the mobilization and accumulation of Cr at the sediment water interface in an electric field at varying different positions and conditions of the electrode arrangement.The tests were carried out with a natural sediment containing heavy metals from the river Weisse Elster (Germany).The electrokinetic experiments have been performed in columns filled with sediment using electrodes made of conductive polymers (polyethylene with carbon black) at a maximum current density of 0.5 mA/cm2. The experimental results suggest that the mobilization and accumulation of Cr highly depends on chemical factors for e.g., pH value, redox potential, respectively redox status and the content of Fe, Al and organic matter in the soil or sediment. The sorption of Cr (III, VI) is very high in the pH range > 4.5. As expected, a high mobilization of Cr (III, VI) was seen in the case of the experiments with the anode at the sediment, because the pH value was lower than mentioned above. On the opposite, the best conditions for the Cr (III, VI) immobilization is high pH values (cathode at the sediment).

The purpose of this study was to assess exposure of four trihalomethanes (chloroform, bromodichloromethane, dibromochloromethane and bromoform) in drinking waters of Okinawa Island and Samoa. Trihalomethanes compounds were determined in the drinking water samples that were collected from the selected consumption sites and treatment plants of both Okinawa and Samoa in 2003-2004. The Chatan and Nishihara Water Treatment Plants (Okinawa) uses both ozonation and chlorination for primary and secondary disinfection. For Samoa Water Treatment Plants only chlorination is used as primary disinfection. Results showed that the mean concentration of trihalomethanes from treatment plants in Okinawa ranged from 0.30 ± 1.81 mg/L to 11 ± 2.68  mg/L and from the consumption sites ranged from 2.08 ± 0.32 mg/L to 19.39 ± 100 mg/L. In comparison, the mean concentration of trihalomethanes from the treatment plants in Samoa ranged from 226 ± 81.2 mg/L to 267 ± 92.3 mg/L and from the consumption sites were in the ranges 212 ± 101 mg/L to 387 ± 125 mg/L. Brominated compounds were commonly seen in all samples collected in Okinawa. Among the trihalomethanes compounds, chloroform was the common detected trihalomethanes in the samples collected from Samoa. The trihalomethanes levels in all samples collected in Okinawa and Samoa were generally below the guideline values in Japan, but some samples displayed levels which exceeded the level of Japan Water Quality and WHO Standards for chlorinated and brominated compounds.

The potential of three Azotobacter chroococcum strains for whey degradation and alginate production were investigated. After dilution, samples were spread plated on isolation agar and Manitol agar and incubated at 30 °C for 24 h. Microorganisms were screened for their ability to whey degradation and alginate production based on colony morphology, negative and capsule staining, ability to decrease the apparent turbidity of the fermentation broths in batch and semi continuous culture by spectrophotometer assay at 400 nanometer and tensiometer assay. Of the three strains tested for whey degradation, only Azotobacter chroococcum 1723 produced significant apparent growth on whey broth and could decrease about 70% of turbidity in fermentation broth during 6 days in batch culture. Colonies of this strain was characteristically yellow, large, moucoid and slimy on whey agar than Manitol agar after 24 h at 30°C. Transmission electron microscopy assay and Carbazole reagent were used to recognize the alginate biopolymer. After optimizing environmental factors such as pH, salt concentration and temperature, this strain was able to produce exopolysaccharide greater than 5 mg/mL. Optimum results were obtained when using whey broth as a fermentation medium without extra salt, temperature at 35 °C and pH 7. Increasing inorganic and organic nitrogen sources (yeast extract and NH4NO3) reduced whey degradation at least 30%. Transmission electron microscopy assay showed a net-structured polysaccharide capsule around the cells. Semi-continuous culture results demonstrated that, alginate production as well as whey degradation was decreased (1 mg/mL and 30 %).

The Mediterranean seagrass Posidonia oceanica (L.) leaf sheaths were used as low cost, available and renewable biological adsorbent for the removal of reactive textile dye from aqueous solutions. Batch experiments were carried out for sorption kinetics and isotherms. Operating variables studied were temperature, pH and chemical pretreatment. Biosorption capacity seems to be enhanced by increasing the temperature. Maximum colour removal was observed at pH 5. Pre-treating fibres with H3PO4 and HNO3 solutions increased the adsorption efficiency up to 80 %. Experimental sorption kinetic data were fitted to both Lagergren first-order and pseudo-second-order models and the data were found to follow first-order equation for raw fibres and pseudo-second-order for pre-treated ones. Equilibrium data were well represented by the Freundlich isotherm model for all tested adsorption systems. Besides, the thermodynamic study has showed that the dye adsorption phenomenon onto P. oceanica biomass was favourable, endothermic and spontaneous.

Factor analysis was applied to the hydrochemical data set of Manukan Island in order to extract the principal factors corresponding to the different sources of variation in the hydrochemistry. The application of varimax rotation was to ensure the clear definition of the main sources of variation in the hydrochemistry. The geochemical data of dissolved major, minor and trace constituents in the groundwater samples indicates the main processes responsible for the geochemistry evolution. By using Kaiser normalization, principal factors were extracted from the data for each location. The analysis reveals that there are four sources of solutes: (1) seawater intrusion; (2) leaching process of underlying rock mediated by pH; (3) minerals weathering process and (4) dissolution of carbonate minerals characterized by high loadings of Ca, Zn and Mg. Such processes are dominated by the significant role of anthropogenic impact from the over abstraction of fresh water from the aquifer. Those factors contributed to the changes of the groundwater geochemistry behavior explain the effect of rising extraction of freshwater from the aquifer.

Nile Rose Plant was used to study adsorption of several cations (Cu2+, Zn2+, Cd2+ and Pb2+) from wastewater within various experimental conditions. The dried leaves of Nile Rose Plant were used at different adsorbent/ metal ion ratios. The influence of pH, contact time, metal concentration, and adsorbent loading weight on the removal process was investigated. Batch adsorption studies were carried out at room temperature. The adsorption efficiencies were found to be pH dependent, increasing by increasing the pH in the range from 2.5 to 8.5 exept for Pb. The equilibrium time was attained within 60 to 90 min. and the maximum removal percentage was achieved at an adsorbent loading weight of 1.5 g/50 mL mixed ions solution. Isothermal studies showed that the data were best fitted to the Temkin isotherm model. The removal order was found to be Pb2+> Zn2+> Cu2+> Cd2+. The surface IR-characterization of Nile rose plant showed the presence of many functional groups capable of binding to the metal cations.

Perylene and penta-aromatic hydrocarbons were determined in sediments as part of a study that was dedicated to the aquatic ecosystem of Elelenwo Creek (Southern Nigeria) in order to carry out a critical corroboration of occurrence and diagenetic evolution of perylene in the sediments of the creek. The results show that the annual mean levels of Benzo [g, h, i] Perylene ranged from 209.00 – 245.28 mg/kg dry weight at the various stations sampled. Meanwhile, Station 3 recorded the highest mean level of 245.28 mg/kg dry weight. The observed values for total penta-aromatic hydrocarbons were high (787.00 - 1154.36mg/kg dry weight) in all the stations sampled. In addition, the highest mean value of 1154.36mg/kg dry weight was again recorded at station 3 for the penta-aromatic hydrocarbons. One origin index or concentration ratio of Ip/Ip+BghiP was also used to evaluate the suitability of the penta-aromatic hydrocarbons as a tracer to distinguish between contaminations arising from different sources. The values for the sampling stations therefore ranged from 0.41 to 0.43. A critical appraisal of the PAH index, consequently, suggested that petroleum combustion is the major penta-aromatic hydrocarbon source in sediments of the creek. The PAH group profile shows that perylene was high in the sediments and would pose apparent effects in fauna. The high concentration of perylene in the sediments was also indicative of an in situ biogenic derivation. Furthermore, a concentration of perylene > 10 % of total penta-aromatic hydrocarbons established a credible diagenetic origin.

Effects of contaminated soil with spent oil on germination, above ground height and biomass of six herbaceous plant species were investigated by conducting a general phytotoxicity test and growth inhibition assessment. Six local plant species were used in order to investigate plant’s ability to germinate and survive in a gradient of contaminated soil with spent oil. The species selected for this experiment include one species of Fabaceae (Medicago truncatular), four species of Gramineae (Bromous mermis, Secal seral, Triticum sativa and Agropyron deserterum) and one species of Linaceae (Linum ussitasimum). Inhibitory effect of contaminated soil on germination, height of young seedling and dry weight were measured. In this study an artificial soil with a light texture included 85% sand, 10% silt and 5% clay was used. The exposure to the contaminated soil carried out using four consecutive concentrations (25, 50, 75, 100 g/kg). Results obtained from the current investigation indicate that all species perform dose-dependent responses to the contaminated soils. Reduction in germination, above ground height and biomass for all species were significantly (P<0.05) different when compared to their controls, however, Medicago truncatular performed the highest and Linum ussitatisimum the lowest inhibitory effect for germination, above ground height and dry weight of seedling.

The study was conducted with the selected soil profile of burnt (soil around brick kilns) and unburnt (agricultural land) soils in the Dinajpur, Rangpur, Rajshahi, Khulna and Patuakhali districts at the western part of Bangladesh to evaluate the effects of brick kilns on soil degradation and environmental pollution. The pH values of the unburnt soils increased as a function of the soil depth for Rangpur, Khulna and Patuakhali, while decreased for the soil profiles in Dinajpur. Burning of soils significantly (p<0.05) decreased the average pH values of soils by 0.4 pH units (7 % increased over average content = IOAC), but strikingly increased the average EC values from 0.26 to 1.77 mS/cm (592 % IOAC) and the effect was pronounced with the depth function. The average sand content of the soil profiles increased by 330%, while the silt and clay contents decreased by 49 and 40 %, respectively. The average losses arising from the burning of agricultural soils were amounted to 63% for organic matter, 56 to 86 % and 23 to 88 % for available and total N, P, K and S, respectively. This huge loss through the burning of 1 m deep soil profile, i.e. almost 3/4th of the deterioration of soil fertility is not only reducing the crop production but also polluting the associated environment and atmosphere. The burning of enormous C, N and S not only degrade the agricultural soils but also contributing to the changes in the global climate.

A new constructed wetland was built to purify one polluted river in Taiwan, and this study was conducted to evaluate the treatment efficiency of the wetland. Due to the very limitation of available budget, several water quality items, which were stipulated by Taiwan’s Environmental Protection Administration for rivers, in the influent and effluent of wetland were analyzed and evaluated. These items included water temperature, pH, DO, BOD5, TSS, and NH4 +-N. The results showed that the average removal rates of total (unfiltered) BOD5, TSS and NH4+-N were 36.9 %, 71.8 % and 47.1%, respectively. With the HRT more than 3.4 days, the wetland could treat the polluted river water effectively. Longer HRT in this wetland appeared no obvious improvement on the removal rate of TSS or NH4+-N. However, BOD removal rate increased while the HRT (Hydraulic Retention Time) increased to about 5 days. In this wetland, the calculated mean first order reaction rate constant (kT) for BOD5 was 0.15/day with a standard deviation of 0.13/ day and for NH4+-N was 0.24/ day with a standard deviation of 0.18/day. It is also concluded that there is a linear proportional relationship between BOD concentrations in the effluent of wetland and its influent mass loading rates, with the coefficient of determination (R2) of 0.6511. Similar result was seen for NH4+-N as well, with the coefficient of determination (R2) of 0.5965. TSS removal rate was found to be linearly proportional to its influent mass loading rate, with the coefficient of determination (R2) of 0.4875.

Drinking water treatment residuals (alum) are waste products of water purification that have potential for environmental remediation as a soil amendment and a potential plant growth medium. In this study, the influence of added Drinking water treatment residuals on the extractability and availability of phosphorus to plants; determination of the agronomic rate of alum to different agricultural soils and evaluation of the alum as ameliorating material for soil conditions and plant growth were investigated. In all studied soils, increasing drinking water treatment residuals rate up to 30 g/kg significantly increased dry matter yield. Application of 10, 20 and 30 g/kg alum significantly increased plant P concentrations in the plant materials (shoots and roots) taken from clay, sandy and calcareous soils. Further increase in alum application rate has resulted in negative significant impact on plants P concentration, especially in clay and calcareous soils, but in sandy soils the increase in phosphorus concentration extended to 40 g/kg alum rate. Application of alum at rates up to 30 g/kg significantly increased available phosphorus concentrations of the three studied soils. However, application of alum at a rate of 40 g/kg to clay and calcareous soils significantly decreased available phosphorus concentrations. Combined analyses of all soils and alum rates studied clearly indicated significant relationship between available phosphorus concentration and phosphorus uptake (r = 0.87, P < 0.001). Based on our experiment results, the rate of 30 g/kg is considered the best application rate of alum because of its positive effects on plant dry matter. Our study clearly demonstrates that alum has potential as a soil amendment to increase plant growth; however, more research is needed to determine beneficial and / or detrimental aspects of this practice under field conditions.

The speciation of metals in environmental samples is a critical factor in assessing the potential environmental impacts, before their disposal. The distribution and speciation of toxic heavy metals in plating wastewater residues and sludge was investigated for four samples using sequential extraction method. Tessier method was used to fractionate the metal content into exchangeable, acid extractable, reducible and oxidizable fractions. Residual and total metal contents were determined in aqua regia digest. The extracts were analysed for metals using inductively coupled plasma -atomic emission spectrometry. The bioavailable fraction (exchangeable and acid extractable fractions) is comprised less than the other forms. The oxidisable and reducible forms are dominants for all the four samples studied. The major metal constitute in the samples is iron, the wastewater residue contains (12.3 and 7.4 g/Kg respectively on dry basis) and the sludge contains (31.5 and 41.6 g /Kg) respectively. Cr concentration is higher in wastewater residue of second electroplating industry. The descending order of the average total metal contents for these four samples were Fe > Cr > Sn > Zn >Cu > Ni > Mn > Pb > Cd > Ag. Based on the average of absolute values for the four samples the highest bioavailability order of metals is Cr (39 %) in wastewater residues and Zn (32 %) in sludge samples. Metal recovery was good, with < 10 % difference between the total metal recovered through the extractant steps and the total metal determined using aqua regia extract.

There is a need to find cheaper and simpler techniques for rural water filtration system in developing countries. Using a filter made of blocks for the water treatment enables one to make vertical filters. It is expected that the amount of land utilized would decrease by more than 70 % if vertical filters were used. The operation and washing would be simpler than using horizontal sand filters as filters made of blocks would be used instead. The feasibility study focused on finding adequate materials, compositions and methods of making a block with enough resistance to water pressure, sufficient porosity for water transformation, and using inexpensive, readily available materials. A pilot study was used to determine an appropriate thickness. Testing the porous filter in another pilot study using the low overflow rate of river water showed biological growth in that media and an adequate efficiency of about 90-100 % was obtained for decreasing the coliform bacteria. Washing in this filter is possible. The amount of water necessary for backwashing is 2.9 % of total amount of water, which is passed.

In the recent decade, biosynthesis of the degradable biopolymers polyhydroxyalkanotes in transgenic yeasts became an important research task. Most research strategies depend on either metabolic engineering or molecular approaches. In the present work, research compared PHA biosynthesis in two types of yeasts; Saccharomyces cerevisiae and a non-convenient Kloeckera spp. Yeast strains were equipped in their cytoplasm with the phaABCRe operon containing genes phbA, phbB and phbC of the PHA biosynthetic pathway of Ralstonia eutropha, which encode β-ketothiolase, NADPH-linked acetoacetyl-CoA reductase and PHA synthase, respectively. The transgenic strains Saccharomyces cerevisiae and Kloeckera sp. were able to produce PHA. The maximum content of the polymer detected in the recombinant strain INVSc1/PHA1 was 2.68 % and only poly-3-hydroxybutyrate (PHB) accumulated. However, the non-conventional transgenic strain KY1/PHA was able to accumulate as maximum of 7.06 % of the copolymer poly-(3-hydroxybutyrateco- poly-3-hydroxyvalerate) (PHV). Western blot analysis confirmed expression of the phaABCRe operon in the transgenic yeast strains. The nature of the PHA thus produced by all tested strains was analyzed by 1H and 13C nuclear magnetic resonance (NMR) spectroscopy.

Concentrations of organochlorine pesticides (Lindane, Aldrin, Dieldrin, Endosulfan, DDT and DDE) residues in beef samples from the Kumasi and Buoho abattoirs in Ghana were determined using gas chromatography. Organochlorine residues were found in all the samples. The average concentration of lindane in beef fat samples from Kumasi was 4.03  mg/kg and 1.79 mg/kg in beef fat from Buoho. The average levels of lindane were 2.07 mg/kg for lean meat samples from Kumasi abattoir and 0.60 mg/kg in lean meat samples from Buoho. Endosulfan concentration in meat samples from Buoho was 2.28 mg/kg in the fat and 0.59 mg/kg in the lean beef. 1,1-dichloro-2,2-bis(pdichlorodiphenyl) ethylene (DDE) recorded mean concentrations of 118.45 mg/kg in beef fat and 42.93 mg/kg in lean beef samples from Kumasi abattoir. Beef samples from Buoho had DDE concentration of 31.89 mg/kg in the fat and 5.86 mg/ kg in the lean beef. 1, 1, 1-trichloro-2, 2-bis-(4'-chlorophenyl) ethane (DDT) recorded an average concentration of 545.22 mg/kg in beef fat and 18.85 mg/kg in lean beef samples from Kumasi abattoir. The average concentration of DDT in beef fat from Buoho was 403.82mg/kg but lean meat samples from the same sampling site recorded mean concentration of 10.82 mg/kg for DDT. Although, most of the organochlorine residues detected were below the maximum limits set by the FAO/WHO, bioaccumulation of these residues is likely to pose health problems in higher organisms like human beings.

Open burnt clay was studied as a potential adsorbent for the adsorption of Congo red (a reactive dye) from aqueous solution. The effect of contact time, pH, adsorbent dosage and temperature were studied. It was observed that the amount of Congo red retained increase with decreasing pH and increasing initial concentration. Removal percentage at pH 2 and 3 are almost same. The adsorption capacity of regenerated burnt clay was showed more than 98 % recovery of the adsorption efficiency of initial virgin adsorbent. The equilibrium data were described well by both Langmuir and Freundlich isotherm model. The adsorption capacity of some natural adsorbents, namely rice husk, wood charcoal, tea waste etc. were also investigated and compared with that of open burnt clay.