Journal of Health and Safety at Work
Year:2017 | Volume:7 | Issue:1 |Papers Count:8

Introduction: Occupational exposure to crystalline silica increases the risk of lung cancer and restrictive lung disease with extensive fibrosis. Silica dust is a major health hazard in foundry factories. The aim of this study was to determine core making workers’ exposure to respirable crystalline silica dust in a foundry factory.Material and Method: This cross-sectional study was conducted in core-making unit of a foundry factory in 2015. Occupational exposure of 55 workers to respirable crystalline silica aerosols was evaluated by using the improved NIOSH7602 method in core-making unit. Risk assessments for silicosis and excess lifetime risk of mortality from lung cancer were done according to Manettej and Rice models, respectively. Data was analyzed with Spss19 software.Result: The mean of respirable crystalline silica dust was 0.246±0.351 (mg/m3). All workers’ exposure to respirable crystalline silica was higher than recommended occupational exposure limits. Silicosis mortality risk and excess lifetime risk of mortality from lung cancer were estimated in the range of 6-63 and 65 per thousand people, respectively.Conclusion: The mean of workers’ exposure to respirable crystalline silica was higher than recommended occupational exposure standards in core making unit. The risk assessment of silicosis mortality and excess lifetime risk of mortality from lung cancer were higher than acceptable levels of risk.

Diazinon is commonly used for pest control in the agricultural fields because of its relatively low cost and high efficiency. Due to the increasing application of pesticides, reliable and accurate analytical methods are necessary for their monitoring. This work was aimed to design the high selective electrochemical sensor for determining of diazinon in biological and environmental samples. The composition of sensor was modified with multi-walls carbon nanotubes and a molecularly imprinted polymer (MIP). A diazinon MIP was synthesized and applied in the carbon paste electrode (CP). The prepared sensor was used to determine the concentration of analyte. Parameters affecting the sensor response, such as sample pH, electrolyte concentration and its pH, and the instrumental parameters of square wave voltammetry, were optimized in different levels to select the optimum conditions for analysis of diazinon. The MIP-CP electrode showed very high specificity for determining the analyte. The obtained linear range was 1×10-6 to 5×10-10 mol L-1. The detection limit was 2.7×10-10 molL-1. This sensor was successfully used to determine the diazinon in environmental and biological real samples without special sample pretreatment before analysis.

Introduction: To evaluate heat stress in the workplace different indices are used. But, none of these measures have been widely accepted. The aim of this study was to determine effective criteria in selecting a heat stress index and weighting of these criteria.Material and Method: This study is a qualitative study that was designed and conducted within 10 stages. In the current study, effective criteria for choosing a heat stress index was determined by using Delphi technique and expert’s opinions (30 people), and then the fuzzy analytic hierarchy process was used for weighting and prioritization of these criteria.Results: Analyzing the completed questionnaires by the experts and according to the percentage of respondents, 11 criteria were finally selected. “Simplicity” criteria by %76.6 had the highest percentage of response. But, the relative weight of this criteria was 0.041, and had the lowest weight after the “low cost” criteria. The criteria relating to the “Standard” item was 0.141as the highest relative weight.Conclusion: It can be concluded that the first step to have a reliable and accurate measurement is to choose a proper and correct index. Based on specialists and expert’s opinions, standardization of the index is the most important selection criteria. Other criteria that must be considered were accuracy, reliability and good correlation with the physiological strain indices.

Introduction: Metro driving is one of the newest jobs in Iran. There are few studies in this field. Therefore, the physical workload and their influencing factors have not been identified in metro driving. The objective of this study was task and physical workload analysis of metro driving to recommend control measures.Material and Method: In this mixed method study, task analysis and Quick Exposure Check (QEC) were used to assessment of physical workload in metro driving. Different methods and techniques including field investigation, document reviews, individual and focus group interviews, and focus group discussions were used to analysis physical workload to recommend control measures.Result: Whole body exposure with physical workload was assessed unacceptable in metro driving. Although the exposures in back, shoulder/arm and hand/wrist were under threshold 70%, neck exposure lead to over physical workload in the whole body. Many themes include unsupported body; non-sufficient view on the track and on displays; awkward posture and unsuitable layout were extracted as significant factors influencing on physical workload.Conclusion: An intervention plan was recommended to a) support body by chair, platform and footplate; b) optimize a sufficient view on the track and on displays; c) maintain body postures in seating position with easy reaching distance and sufficient view; and d) design a suitable layout for driving panel regarding to controls, keys and displays.

Introduction: Exposure to crystalline silica dust can seriously threaten health of workers engaged in processes such as casting, stone crushing, grinding, construction activities, insulator manufacturing, and glassblowing and sandblasting. The aim of this study was to assess occupational exposure to crystalline silica and to determine the risk of mortality from silicosis and lung cancer in an insulator manufacturer.Material and Method: Air personal sampling was performed using 10 mm nylon cyclone and mixed cellulose ester (MCE) membrane filters (5 mm diameter, 0.8 mm pore size) for 60 male workers. Samples were prepared and analyzed according to the National Institute for Occupational Safety and Health (NIOSH) 7601 standard method. The risk assessment of mortality due to silicosis resulting from crystalline silica exposure was done by using model of Mannetje et al. for the period of 10 years. The mortality rate of lung cancer was determined using a linear regression model derived from the study Rice et al.Result: The highest and lowest exposure levels to silica were belonged to the packing unit (0.54±0.28 mg/ m3) and the furnace (0.02±0.01 mg/m3), respectively. Crystalline silica concentrations for all samples were higher than Threshold Limit Values (0.025 mg/m3) recommended by the American Conference of Governmental Industrial Hygienists (ACGIH). According to Mannetje et al. model, the cumulative exposure of 25% workers was in the range 0 to 0.99 that it represents 1 death per 1,000 people. The risk of mortality due to lung cancer was obtained in the range of 7-94 persons per 1000 workers exposed to silica.Conclusion: In general, the geometric and arithmetic mean of crystalline silica exposure was higher than threshold limit value for most of the subjects. For all workers of the insulator manufacturer, the risk of silicosis related mortality was higher than 1/1,000 (unacceptable level of risk). Predicting the lung cancer mortality from silica exposure indicated a high level of mortality risk among understudied workers.

Introduction: One of the important consequences of globalization and development, especially in developing countries, are occupational accidents. As, today the economic burden due to these accidents is remarkable on the country’s economy. The aim of this study was financial estimate of the productivity loss due to work-related deaths in Iran in 2013.Material and Method: In this study, occupational accident data were used registered in the environmental and occupational health center, in Iranian Ministry of Health and Medical Education. A formula used by the Centers for Disease Control and Prevention America (CDC) was used to estimate the productivity loss. Finally, after replacing the necessary parameters amount of productivity loss was calculated.Result: The total lost years of life were calculated 1293.15 years due to the deaths caused by occupational accidents. The total amount of monetary loss due to the productivity loss in the country, was estimated 730513.06 Rials. The greatest loss was in the 59-50 years old age group.Conclusion: The negative rate of productivity, the large quantity of the discount rate, low life expectancy in the country as well as the low wages of the workers, are the likely reasons for minimal negative impact of the workforce deaths on the country’s productivity.

Introduction: FMEA method is one of the most used techniques in risk assessment and prioritization. But, due to several reasons, its application has been limited to the real-world settings. The aim of this study was to deal with these restrictions using the combined fuzzy (in terms of the Z-numbers) and grey (in terms of the grey relational analysis) theories.Material and Method: The current study is an analytical cross-sectional survey that was performed to prioritize the failure modes of the overhead cranes. Initially, an FMEA team including 4 specialists was established. Then, the opinions of the team members were gathered in terms of the Z-numbers and the weights of the risk factors (O، S, and D) were determined using the fuzzy AHP method. Finally, the failure modes were prioritized using the GRP method.Result: From 13 cases of the identified failure modes, the conventional FMEA was assigned equal priority to the 7 cases and as a result 9 risk priorities were determined. But, in the proposed method, because of the elimination of the restrictions of conventional FMEA, 13 risk priorities were assigned to the failure modes. Conclusion: Relying upon the fuzzy AHP, Z-numbers and GRP method, the proposed method dealt with the equal weights of the risk factors, fuzziness of the data (expert’s judgments) and the prioritization of the failure modes. The proposed method has more capabilities in relation to the conventional FMEA for prioritization of the failure modes.

Introduction: Work-Family Conflict can influence the physical and mental health of workers as a social parameter. The aim of this study is supposed to provide theoretical model of relationship between work-family conflict and occupational accidents, taking into account parameters such as job stress and general health of employees in a steel manufacturing industry.Material and Method: Research population included workers of steel department of a steel manufacturing industry. This research was a cross-sectional study, and 270 individuals were selected in two groups, with an accident experience during lasts 5 years (case) and without (control). They responded to questionnaires including 4 parts, demographic, 18 questions of work-family conflict, 35 questions of job stress and, 28 questions of general health. Data were analyzed and introduced using AMOS software.Result: Result showed that the model present an excellent goodness of fit and all of factors were significant between parameters (p<0.001). In addition, individual health and job stress with high coefficient could affect work-family conflict and work-family conflict was effective in the event of occupational accidents.Conclusion: Reducing work-family conflict as a social parameter affecting stress can be effective in the reduction of occupational accidents. The organizational management system with optimization of this important factor can upgrade its level of occupational safety.